NEWS
VIDEO NEWS
NEWS CENTER- > NEWS -> INTRODUCE
 
Zhongneng vacuum oil dehydrator plants
DATE:2017-5-9  FROM:ZN  AUTHOR:ZN  DOWN:140
 
Zhongneng vacuum oil dehydrator plants




If the hydraulic, lubricating, compressor, or gear oil you use is not water base in formulation, then water is considered a contaminant and must be recognized and managed.  There are three types of water in a typical system; free water, emulsified water, and dissolved water.  Most oils' water saturation point, that point above which water is in a free form, is 200-400ppm, depending on age and condition. Using 100ppm for an upper water limit for most systems using mineral base oils, this means all free & emulsified water and a significant portion of dissolved water must be removed.  A vacuum dehydrator is one of the very few methods to remove dissolved water from oil.  Let's take a look at these three types of water in your system. It will give you a solid foundation for how the vacuum dehydrator works in the end.


Free water


Free water is separate from the oil in the system and can be visually identified in a sample bottle from the oil.  Most oils' specific gravity is less than 1.00, so water usually collects at the bottom of the sample bottle or reservoir/system.  Due to this reason free water can easily be decanted, or removed by draining through a reservoir drain port.  Decanting is recognized as a smart step, if available, even when using a vacuum dehydrator to increase the water removal speed.


Emulsified water


Emulsified water is water that has blended with the oil.  Even though emulsified water in oil is in a free form, emulsified water will mostly remain in this blended state and not 'fall out' or separate and settle on the bottom like free water.  Emulsified water must be addressed.  Water absorbing and coalesce technologies will have difficulties addressing emulsified water.


Dissolved water


Dissolved water is water that has been dissolved into the oil, just as humidity is a measure of the amount of water dissolved in the air, or sugar being dissolved into tea. As temperature of the air or tea rises, the capacity for more dissolved water or sugar increases. Similarly, when the temperature of oil rises, the capacity to absorb water rises, but to a point.  Any extra water cannot be dissolved and is free flaoting with the oil.  We then call this water free water.  After all free and emulsified water is removed, the vacuum dehydrator then focuses solely on dissolved water.  By this time the vast majority of water in the system has already been removed.  Removing dissolved water is the slow process.  It is highly recommended the vacuum dehydrator uses a water % saturation meter so the amount of dissolved water in the oil can be confirmed in real time.  If the machine is not fitted with a % saturation meter, capture an oil sample and perform Karl Fischer titration to confirm actual ppm down to single digits.  Crackle test is not recommended since it will only show presence of water above 500ppm.  Infrared test is not recommended with water levels expected to be <1000ppm.


So what is a vacuum dehydrator?


A vacuum dehydrator is a total water removal machine designed to be attached to an online or offline system/reservoir/barrel to remove all free & emulsified water and upwards of 90+% of dissolved water.


How does it work?


In a nutshell, a vacuum dehydrator heats the oil (130-160F), if necessary, and draws a vacuum (18-27"Hg) on the oil.  Raising temerature while drawing a vacuum causes water to flash to steam at a temperature low enough not to cause thermal breakdown of the oil.


At sea level water flashes to steam at 212F.  The target zone for vacuum dehydration is 130-160F, but the oil will dictate this temperature.  A very stable synthetic oil may require a hotter temperature than a standard mineral oil.  Draw a higher vacuum to flash water to steam at a lower temperature, keeping in mind a higher vacuum is slower water removal than lower vacuum, so choose your balance between low temperature and water removal rate.


If there is excess water in your system check out our vacuum dehydrator. It works with any system and on all oils from mineral base to synthetic to exotic, ranging up to ISOVG1000 oils. Best of all, it's guaranteed to remove the unwanted water in your system to your target of <100ppm and further if needed.


There are other ways to remove free water from the system, such as water absorbing filter elements and coalesce technology on limited oils without aggressive additive packages.  However, to possess the capability to remove water from every oil onsite regardless of additive package or oil type or viscosity (up to ISOVG1000), vacuum dehydrator is the only real option available for portability and complete water removal.


If you work in a saw mill, steel mill, power plant, costruction site, drill rig or any place that uses hydraulics/lube/gear/compressor oils and have issues with water, give us a call.  If your extra oil barrels sit outside in the environment, you will have water in your oil.  The barrel breathes in/out with temperature change. It's not a matter of if, but when we will need to address water contamination for what it is, an unwanted contaminant.  You don't want it there.  Its doing damage as we speak. 


 


Welcome to contact us for detailed solution for your oil contamination by unwanted water anytime!


  Print Previous
 
 
Copyright © 2006 zhongnengcq.cn All rights reserved. Chongqing Zhongneng Oil Purifier Manufacture Co.,Ltd.
Address:No. 101 Huoju Street, Jiulong Industrial Park, Jiulongpo District, Chongqing, China
Tel: 0086-23-68060921 Fax:0086-23-68060921 Postcode:400039 E-mail:sales@zhongnengcq.cn